Gebruikershandleiding Whirlpool 8318507 Washer/Dryer

Gebruikershandleiding voor het apparaat Whirlpool 8318507 Washer/Dryer

Gebruikershandleiding Whirlpool 8318507 Washer/Dryer

Extracten van inhoud

Inhoud van de samenvatting op de pagina nr. 1

Printed in U.S.A.83185072000Benton Harbor, Michigan 49022Part No. 8318507©2000 Whirlpool CorporationBenton Harbor, Michigan 49022CORPORATIONCall your dealer or local authorized service company.When you call, you will need the washer model number and serialnumber. Both numbers are on the model/serial rating platelocated under the washer lid and on the top of the washer./Need assistance?®HomeAppliances120-volt, 60-Hz120WasherInstallationInstructionsTable of ContentsIntroductionPages 2 - 32-3Requ

Inhoud van de samenvatting op de pagina nr. 2

Introduction.Locationof washerYour safety and the safety ofothers are very important.We have provided many important safety messages inthis manual and on your appliance. Always read and obeyall safety messages.This is the safety alert symbol.This symbol alerts you to potential hazards thatcan kill or hurt you and others.All safety messages will be preceded by the safety alertsymbol and the word “DANGER” or “WARNING”. Thesewords mean:DANGERYou can be killed or seriously injured if youdon

Inhoud van de samenvatting op de pagina nr. 3

Recessed areaor closetThe installation dimensions shown are the minimum spacesallowable. Additional spacing should be considered for ease ofinstallation and servicing.If closet door is installed, the minimum air openings in top andbottom of door are required. Louvered doors with air openings intop and bottom are acceptable.Companion appliance spacing should be considered.* Additional clearances for wall, door and floor moldings may berequired.*Side viewFront viewFront view (door not shown)closet

Inhoud van de samenvatting op de pagina nr. 4

RequirementsElectrical!! WARNING!! WElectrical Shock HazardPlug into an earthed outlet.Do not use an adapter.Do not use an extension cord.Failure to follow these instructions can resultin death, fire or electrical shock.If codes permit and a separate earthing wire is used, it isrecommended that a qualified electrician determine thatthe earthing path is adequate.120120-volts, 60-Hz, AC-only, 15- or 20-ampere, fused electricalsupply is required. Time-delay fuse or circuit breaker isrecommended. It

Inhoud van de samenvatting op de pagina nr. 5

EInstallation StepsBCHGDFAFCEEAPreparationSLIDE WASHER ONTO CARDBOARD OR HARDBOARDBEFORE MOVING ACROSS FLOOR.Move washer close to its final location.Read, then remove the label (E) that covers the power supplycord.EA(E)(A)Remove shipping strap (A).Completely remove the shipping strap with 2 cotter pins (B) fromthe inside of the washer.2(B)Pull the strap completely out of the washer.BPull firmly to remove the other end of the shipping strap (C) fromthe back of the washer to release self-leveling

Inhoud van de samenvatting op de pagina nr. 6

CDrain hoseconnectionIMPORTANT: THIS PROCEDURE MUST BE FOLLOWED TOASSURE PROPER INSTALLATION.PAMCLCTo prevent the drain hose from coming off or leaking, it must beinstalled per the following instructions.• Wet the inside end of the drain hose (A) with tap water. DONOT USE ANY OTHER LUBRICANT.• Squeeze ears of one drain hose clamp (B) with pliers to openand place clamp over the end of the drain hose.• Open clamp and push end of drain hose onto drain connector(C) until hose contacts ribbed s

Inhoud van de samenvatting op de pagina nr. 7

ELevelingwasherStack two corner posts (A) on top of each other. Tilt washerbackwards and slide corner posts under washer 7.6 cm (3inches) from each side of washer as shown.(A)7.6A1.3 cmBScrew nut (B) down on legs to within 1.3 cm (1/2 inch) ofbase (C).(1/2")(B)(C) 1.3CDInsert legs into correct holes at each front corner of washer untilnuts touch washer (D). DO NOT tighten nuts until washer is level.(D)Tilt washer backward and remove corner posts. Gently lowerwasher to floor.Move washer to its fi

Inhoud van de samenvatting op de pagina nr. 8

Continued from page 7.7Check that hose is not twisted or kinked and is securelyin place.CBD(B)Put “hook” end of drain hose in laundry tub (B) or standpipe(C). Tightly wrap the shipping strap (D) around the drain hoseand laundry tub or standpipe. Push plug into the nearest hole inthe shipping strap.DEIf the water inlet faucets and drain standpipe are recessed, put“hook” end of drain hose (E) in standpipe. Tightly wrap theshipping strap (F) around the drain hose and faucet body (not thehan

Inhoud van de samenvatting op de pagina nr. 9

Printed in U.S.A.Part No. 8318507©2000 Whirlpool CorporationBenton Harbor, Michigan 4902283185072000Benton Harbor, Michigan 49022CORPORATIONCall your dealer or local authorized service company.When you call, you will need the washer model number and serialnumber. Both numbers are on the model/serial rating platelocated under the washer lid and on the top of the washer./Need assistance?®HomeAppliances120-volt, 60-Hz12060WasherInstallationInstructionsTable of ContentsIntroductionPages 2 - 32-3Re

LEAVE A COMMENT